Choose style:

Author Topic: PEQ 3157100 Pairing with Almond 3 Unsuccesful  (Read 3744 times)

0 Members and 1 Guest are viewing this topic.

Offline jukka69

  • Newbie
  • **
  • Posts: 13
  • Thanks: 0
  • Registered : 07/08/2017
    YearsYearsYearsYearsYearsYearsYears
PEQ 3157100 Pairing with Almond 3 Unsuccesful
« on: October 08, 2017, 07:14:18 am »
I have PEQ 3157100, but I am not able to pair it with the Almond 3. I have followed the guidelines under
https://wiki.securifi.com/index.php?title=3157100

It seems that Almond does not even recognize the device i.e. when I an sending pairing signal from PEQ, nothing changes in the Almond 3 Add sensor screen.

Is there any guidelines for debugging?


Offline mparadis

  • Backer
  • *
  • Posts: 1765
  • Thanks: 3
  • Registered : 02/08/2013
    YearsYearsYearsYearsYearsYearsYearsYearsYearsYearsYears
Re: PEQ 3157100 Pairing with Almond 3 Unsuccesful
« Reply #1 on: October 10, 2017, 01:49:07 pm »
That thermostat is a Z Wave device correct? Do you have the Z Wave Add-on USB stick? Almond 3 only supports Zigbee out of the box without the add-on stick.

Offline jukka69

  • Newbie
  • **
  • Posts: 13
  • Thanks: 0
  • Registered : 07/08/2017
    YearsYearsYearsYearsYearsYearsYears
Re: PEQ 3157100 Pairing with Almond 3 Unsuccesful
« Reply #2 on: October 15, 2017, 08:38:27 am »
Peq 3157100 is ZigBee device and supposed to pair per the above Wiki describes. Was wondering if there is a way to debug to see where the error might be...

Offline Ashok

  • Securifi Staff
  • *
  • Posts: 2770
  • Thanks: 3
  • Registered : 25/07/2014
    YearsYearsYearsYearsYearsYearsYearsYearsYearsYears
Re: PEQ 3157100 Pairing with Almond 3 Unsuccesful
« Reply #3 on: October 16, 2017, 04:33:45 pm »
@ jukka69,

Peq 3157100 is ZigBee device and supposed to pair per the above Wiki describes. Was wondering if there is a way to debug to see where the error might be...

As long as adding procedure is followed properly, there shouldn't be any issue. Do you have any other Zigbee device to test it?

Offline mparadis

  • Backer
  • *
  • Posts: 1765
  • Thanks: 3
  • Registered : 02/08/2013
    YearsYearsYearsYearsYearsYearsYearsYearsYearsYearsYears
Re: PEQ 3157100 Pairing with Almond 3 Unsuccesful
« Reply #4 on: October 22, 2017, 07:02:47 pm »
Peq 3157100 is ZigBee device and supposed to pair per the above Wiki describes. Was wondering if there is a way to debug to see where the error might be...

Yes that was my mistake realized that afterwards, sorry. Not sure why it isn't working then.

 

Page created in 0.057 seconds with 16 queries.

bottleneck