Securifi Community Forum
Securifi Products => Almond+ => Topic started by: Ashok on December 06, 2017, 09:03:51 am
-
Please post any feedback related to Almond+ Firmware R091 here.
-
Installed the Almond+ new firmware.... So far so good....
Presume this is mostly security updates and such....
-J
-
so far so good in case of KRACK.
Lot's of other stuff is outdated and vulnerable so i highly hope that you will fix that also. I saw that you've updated dnsmasq for other almond routers, why this fix wasn't introduced in almond+ firmware?
-
After applying the update, it killed all WiFi for me. After a hard reset, followed by a reboot, all functionality appears to have been restored. I will post again if I run into anymore hiccups.
-
Installed the Almond+ new firmware. Quick and easy. No issues.
-
Noticed that now I can control my power meter switch (Climax_PSS-29ZBSR) over cloud. Thanks!
-
I use my Almond+ as a range extender. From what I can tell, it just doesn't see 5Ghz since the update. I know it is there and all of my other devices can see it, even farther out than the Almond. But when I view the available networks for range extender mode, only 2.4GHz bands appear.
-
I mean... nice of you to address KRACK, but I can't miss this opportunity to remind that you promised to fix OpenVPN client "in the next update" over a year ago
-
Range extender mode does not work for me in new firmware. I've tried resetting the device and setting it up again but that did not help.
I can see my 5GHz network in the list and enter the settings but almond is unable to connect to it. The same setup works on R090 firmware so I downgraded for now.
I also have IPv6 set up. In range extender when I connect to almond I only get IPv4 but no IPv6 from my main network. Shouldn't range extender act like a network bridge and just forward everything to the main network? On another router with openwrt if I set up wireless bridge using relayd I get both IPv4 and IPv6 on extended network from the main network.
This problem is present on all firmwares.
And can relayd package be included in next firmware build on almond so that it can be used for manual bridge setup? If needed I can provide settings for proper bridge setup for openwrt.
-
+1 on range extender mode not working. I had never attempted to use it previously though.
I switched internet providers on Wed, Dec 13th. I didn’t really want to move my Almond+ to the new room where the new modem had to be located, but rather just wanted to turn it into a repeater with all my Z-Wave and wifi devices in place.
In Range Extender mode, t would connect, then disconnect... back and forth, with showing connection on the router screen up for 5-10 seconds, but then down for 10-20 seconds, this cycle repeating 3-4 times before it went down for good. I disabled the mode, then re-enabled the mode, going through the set up process again, but the results were the same.
Rather than downgrading the firmware, I simply moved it to be physically right next to the new U-verse modem/router combo, as it has enough range, so I don’t have to reconfigure any of my wifi devices.
-
Just updated, no issues to report (Almond+ in Router mode).
-
Just noticed what seems to be a major issue when trying to configure any Z-wave device on the Almond+. What I observe is the following:
1. Select a Z-Wave device
2. Press "Configuration" option.
3. Press "Parameter" option, set the parameter number, select OK.
4. Back to the main screen with the "Parameter" field properly set.
5. Set "Size" option.
6. Press "Value" option, set the "Value" number, select OK.
5. Back to the main screen with the "Value" field empty and the "Parameter" field overwritten by the number that was used to set the "Value" field.
6. Since it seems to be impossible to fill the "Value" field, it is never possible to conclude the "Configuration" operation.
Could anyone try to replicate a Z-wave configuration and check if you observe the same?
-
Just noticed what seems to be a major issue when trying to configure any Z-wave device on the Almond+. What I observe is the following:
1. Select a Z-Wave device
2. Press "Configuration" option.
3. Press "Parameter" option, set the parameter number, select OK.
4. Back to the main screen with the "Parameter" field properly set.
5. Set "Size" option.
6. Press "Value" option, set the "Value" number, select OK.
5. Back to the main screen with the "Value" field empty and the "Parameter" field overwritten by the number that was used to set the "Value" field.
6. Since it seems to be impossible to fill the "Value" field, it is never possible to conclude the "Configuration" operation.
Could anyone try to replicate a Z-wave configuration and check if you observe the same?
Yes, I have the exact same issue.
-
Just noticed what seems to be a major issue when trying to configure any Z-wave device on the Almond+. What I observe is the following:
1. Select a Z-Wave device
2. Press "Configuration" option.
3. Press "Parameter" option, set the parameter number, select OK.
4. Back to the main screen with the "Parameter" field properly set.
5. Set "Size" option.
6. Press "Value" option, set the "Value" number, select OK.
5. Back to the main screen with the "Value" field empty and the "Parameter" field overwritten by the number that was used to set the "Value" field.
6. Since it seems to be impossible to fill the "Value" field, it is never possible to conclude the "Configuration" operation.
Could anyone try to replicate a Z-wave configuration and check if you observe the same?
May I know the name and model number of the z-wave device you are trying to configure?
-
I have this issue with any zwave device, but if you want specifics, the most recent one I tried was the GE/Jasco 12721 Smart Outlet.
-
On my case is also with any of the Z-Wave devices I have:
- Popp Smoke Detector with Indoor Siren
- Popp Solar Outdoor Siren
- Fibaro FGS-222 Dual Relay Switch
-
WIFI is now very unstable after the update.
have to reboot 2 or 3 times every day... >:( >:( >:( >:(
-
@ Yaku,
Perform a factory reset and then check the performance.
-
Since the update, the 5GHz disappears about once per day and the router needs to be rebooted. Having to do a factory reset and then setting everything back up, which is what I've seen suggested to others, is probably more of a pain in the butt then rebooting the bunny thing. I'll see if the reset fixes things this weekend, but this definitely does not make me happy.
-
@ Yaku,
Perform a factory reset and then check the performance.
Will do this weekend and report back.
Love my Almond since day 1 but this issues make me nuts.
Just imagine wife complaining because can't browse her Instagram.!!
-
Hi,
I can't connect my chromecast now ...
-
fibaro fgms-001 no motion detection...
cubino flus on/off thermostat can not adjust temp...
-
@ pete82,
Could you please check, if they are working from LCD UI and App and also, send us the logs "Logs for Ashok Pete"
-
@ashok sorry, i put it into the wrong topic, i got the problems with r092 and not R091. Could you move it please. The problems were the same on gui and app. I had to downgrade the firmware back to R091. Now it works again.