Choose style:

Recent Posts

Pages: [1] 2 3 ... 10
1
Almond+ / Re: Any feedback related to Almond+ Firmware R091
« Last post by rlopes on Today at 06:33:39 am »
Just noticed what seems to be a major issue when trying to configure any Z-wave device on the Almond+. What I observe is the following:

1. Select a Z-Wave device
2. Press "Configuration" option.
3. Press "Parameter" option, set the parameter number, select OK.
4. Back to the main screen with the "Parameter" field properly set.
5. Set "Size" option.
6. Press "Value" option, set the "Value" number, select OK.
5. Back to the main screen with the "Value" field empty and the "Parameter" field overwritten by the number that was used to set the "Value" field.
6. Since it seems to be impossible to fill the "Value" field, it is never possible to conclude the "Configuration" operation.

Could anyone try to replicate a Z-wave configuration and check if you observe the same?
2
Almond+ / Re: Popp smoke sensor / siren
« Last post by rlopes on December 16, 2017, 05:21:02 pm »
Any news on the Siren support?

After installing firmware R091, I have noticed that the ability to trigger the siren directly from the Almond+ has been lost. Not that I ever used it (because it was not possible to use it in a "rule") but seems to be a step back on the support of this device.
3
Almond+ / Re: Any feedback related to Almond+ Firmware R091
« Last post by rlopes on December 16, 2017, 04:43:39 pm »
Just updated, no issues to report (Almond+ in Router mode).
4
Almond+ / Re: Adding a Aeotec by Aeon Labs Range Extender
« Last post by Ashok on December 15, 2017, 05:09:12 pm »
@ dimodica1,

What does it show under the LCD UI, and even though the status shows "Unsupported" the functionality should still be working.
5
Almond+ / Re: Any feedback related to Almond+ Firmware R091
« Last post by utrph77004 on December 15, 2017, 11:54:25 am »
+1 on range extender mode not working.  I had never attempted to use it previously though.

I switched internet providers on Wed, Dec 13th.  I didnít really want to move my Almond+ to the new room where the new modem had to be located, but rather just wanted to turn it into a repeater with all my Z-Wave and wifi devices in place.

In Range Extender mode, t would connect, then disconnect... back and forth, with showing connection on the router screen up for 5-10 seconds, but then down for 10-20 seconds, this cycle repeating 3-4 times before it went down for good.  I disabled the mode, then re-enabled the mode, going through the set up process again, but the results were the same.

Rather than downgrading the firmware, I simply moved it to be physically right next to the new U-verse modem/router combo, as it has enough range, so I donít have to reconfigure any of my wifi devices.
6
Almond+ / UK Fibaro Flood Sensor Issue
« Last post by gregghill on December 15, 2017, 10:03:46 am »
Hi All,

I have purchased the Almond+ unit as it was released this month in the UK.

I have successfully, configured it for Zigbee sensors however utilising a Fibaro Flood Sensor I can connect it successfully to the hub but it does not allow any interaction, if its wet the sensor audible alarm sounds but there is no change to the hub and it states it is still 'OK'

Realising there is a difference in ZWave protocol in the US to Europe is it that the UK version of the hub incorporates the US ZWave signal which would be why the sensor is not behaving correctly?  :-\

Any help would be appreciated,

thanks all and Merry Christmas  :D
7
Peanut plug / Re: Opinions on the plug
« Last post by joltdude on December 15, 2017, 10:00:56 am »
Actually am able to get current, on/off status and voltage..
8
Almond+ / RadioThermostat CT30 not updating current temperature
« Last post by td0g on December 15, 2017, 09:04:36 am »
When I add a CT30 to my Almond+ it connects fine but the temperature it was reading when I connected it is all that is ever displayed on the touch screen or in apps.  I have tried removing it and adding it again, it updates to the new current temperature but still never changes after that.  I choose "thermostat" when I add it, I have tried "other" but that doesn't work at all.  Is this a known bug?
9
Android app / Any feedback related to Android App 7.57
« Last post by Ashok on December 15, 2017, 08:53:45 am »
Please post any feedback related to  Android App 7.57 here.
10
Android app / Android App 7.57 is out
« Last post by Ashok on December 15, 2017, 08:52:56 am »
Android App 7.57 is out and available through Play Store, please find the release notes below:

--> Bug fix for + sign not working on few Android devices.

--> Crash fixes.
Pages: [1] 2 3 ... 10

Page created in 0.068 seconds with 16 queries.