bottleneck
Choose style:

Recent Posts

Pages: 1 2 [3] 4 5 ... 10
21
Hey BRO, Try resetting your router settings. Also before that you can try out some of the solutions given here, if you aren't able to login into the 192.168.100.1 i.e. the arris's router default gateway. Check out this link
22
Home automation / Re: Incorrect Sunrise and Sunset Times
« Last post by AcidLotus on April 12, 2019, 01:49:37 am »
@ All,

Our servers have been replaced now and everything should be working just fine. Please check and let us know the status. Thank you!

No, not working correctly yet. Sometime probably around April 7th, I noticed the lights were coming on 15 minutes before sunset again, like they were before Dec. 31st. For the past 2 or 3 days, they haven't been coming on at all before sunset like they are supposed to - Instead they turn on at a set time in the morning and now don't turn off 15 minutes after sunrise like they're supposed to. No changes were made to the schedules at all.
23
Home automation / Re: Incorrect Sunrise and Sunset Times
« Last post by rouz42 on April 11, 2019, 08:02:02 pm »
@ All,

Our servers have been replaced now and everything should be working just fine. Please check and let us know the status. Thank you!

I reset the rules (to use sunrise and sunset) and rebooted the Almond and can confirm that it is NOT working correctly.
24
Almond 3 / Re: Almond 3 locks up with blank white screen
« Last post by anwar.shiekh on April 11, 2019, 04:48:33 pm »
Even though I have some PTC fuses on the way, I have decided for now to just short across the fuse on the board (login to see attached picture).

I am now running with the fuse bridged and await the Summer to see if the Almond 3 can now take the heat.
25
Almond 3 / Re: Almond 3 locks up with blank white screen
« Last post by punkorambo on April 11, 2019, 04:37:48 pm »
Could you please take a picture of what it looks like after your replaced the fuse?
26
Almond 3 / Re: Almond 3 locks up with blank white screen
« Last post by anwar.shiekh on April 11, 2019, 02:15:16 pm »
The PTC fuse is 1.5A 12V and I have decided to go with a non surface mounted version so it stays off the board and so cooler. Login to see a picture of the fuse I think to try and the original fuse location.

The 2015 and A1A Almonds seem to use this off board type.
27
Almond 3 / Screen on hours
« Last post by anwar.shiekh on April 10, 2019, 10:21:30 pm »
I have noticed that after a factory reset that the screen setting (advanced) has the screen on for several hours a day. Not such a great default in my opinion.
28
Home automation / Re: Incorrect Sunrise and Sunset Times
« Last post by Kinggovernator on April 10, 2019, 10:08:33 pm »
Glad to see these are up again. Though Iím not so sure itís correct? My almond is showing my town correctly  but yet as of right now it says itís 72 degrees out and clear with a pic of a sun. Itís 10pm and 44 degrees outside, and windy, 20mph. And the high today was in the low 50ís. Now tomorrow itís suppose to be sunny and in the 70ís. ? Thanks
29
Almond 3 / Transmit power
« Last post by anwar.shiekh on April 09, 2019, 06:55:06 pm »
Is there a way to reduce the transmit power on the Almond? in an attempt to keep it from overheating.
30
Almond 3 / Re: Almond 3 locks up with blank white screen
« Last post by anwar.shiekh on April 09, 2019, 02:41:42 am »
First warm day of Spring and my Almond 3 also went 'white screen of death'; Summer is going to be MUCH hotter.
Pages: 1 2 [3] 4 5 ... 10

Page created in 0.044 seconds with 17 queries.