Choose style:

Author Topic: Keyfob presence  (Read 8120 times)

0 Members and 1 Guest are viewing this topic.

Offline umar

  • Backer
  • *
  • Posts: 102
  • Thanks: 1
  • Registered : 28/04/2014
    YearsYearsYearsYearsYearsYearsYearsYearsYearsYears
Keyfob presence
« on: March 25, 2015, 12:28:41 pm »
It will be nice  to activate and deactivate the alarm automatically with the presence of keyfob..and activate the scenes with the presence of the fob ...

Almond + with 3 Open close sensors,2 Water sensors,4 Key fobs,1 Motion sensor,Everspring SE 812 siren,Fibaro FGWPE-101 zwave wall plug,3 Philips Hue Bulbs. Everspring wall plug AN180-6,Everspring zwave plus micro module dimmer AD146,Fibaro motion sensor,Fibaro smoke sensor,Fibaro Flood sensor

Offline jzh797s

  • Newbie
  • Posts: 2
  • Thanks: 0
  • Registered : 25/03/2015
    YearsYearsYearsYearsYearsYearsYearsYearsYears
Re: Keyfob presence
« Reply #1 on: March 25, 2015, 03:03:01 pm »
I would like to see this as well or preferably bluetooth (ie phone connection) or gps location through the app presence.

Offline fillibar

  • Backer
  • *
  • Posts: 2060
  • Thanks: 4
  • Registered : 02/08/2013
    YearsYearsYearsYearsYearsYearsYearsYearsYearsYearsYears
Re: Keyfob presence
« Reply #2 on: March 25, 2015, 03:57:13 pm »
That may not be possible. The Keyfob is not a presence sense device, but rather a source of a couple buttons. ZigBee sensors report their status, usually on a switch or other state change trigger. They cannot usually be polled to determine if they are around or not.
Almond 3 mesh handling the home.

Amritendu

  • Guest
Re: Keyfob presence
« Reply #3 on: March 25, 2015, 05:05:48 pm »
Sorry, but don't think there would be any support for bluetooth/gps presence.

Offline umar

  • Backer
  • *
  • Posts: 102
  • Thanks: 1
  • Registered : 28/04/2014
    YearsYearsYearsYearsYearsYearsYearsYearsYearsYears
Re: Keyfob presence
« Reply #4 on: March 25, 2015, 05:25:51 pm »
Keyfob had a zigbee puce ...it will be works like zigbee tag non ..so almond plus will know when its enters or leave its zone...i use keyfob to activate and deactivate my alarm ...when i activate my alarm from ground floor with keyfob it wont work ....but when i activate in front of my door it work because i entered in almond plus zone ..

or any other presence tag (zigbee or zwave)that works with almond plus..

Thanks
« Last Edit: March 25, 2015, 05:27:56 pm by umar »
Almond + with 3 Open close sensors,2 Water sensors,4 Key fobs,1 Motion sensor,Everspring SE 812 siren,Fibaro FGWPE-101 zwave wall plug,3 Philips Hue Bulbs. Everspring wall plug AN180-6,Everspring zwave plus micro module dimmer AD146,Fibaro motion sensor,Fibaro smoke sensor,Fibaro Flood sensor

 

Page created in 0.039 seconds with 24 queries.